Archives

PAUX

PAUX

The Punch PAUX is a universal panel mounted input port that allows you to have easy access to USB and Auxiliary audio connections. The port features a front mounted USB and 3.5mm audio connection, which is attached to 6 ft. extension cables terminating at a female USB and male stereo RCA. This port is designed to extend these types of connections from the back of a source unit to an easily accessible spot on the dash or console. This helps eliminate unsightly cables from hanging out of the dash or glove compartment and provides a more secure connection for your mobile devices. The unit mounts in a 1 in. mounting hole and secures with the included retaining nut while the water resistant cover helps to keep out moisture and dirt when not being used.

PBR300X1

PBR300X1

The PBR300X1 is a mono amplifier designed for a subwoofer system that requires little space. The BRT (Boosted Rail Technology) is an ultra efficient design that doesn’t even use a switching power supply to generate its 300 Watts of power! The BRT also has a variable hi-level DC offset turn-on circuit for easy installation into any OEM system. Great for motorcycles and recreational vehicles.

PBR300X2

PBR300X2

The Punch PBR300X2 uses Rockford Fosgate’s patented BRT (Boosted Rail Technology) for an ultra efficient design that does not use a switching power supply to generate its rated power. This allows the chassis design to be much smaller than traditional sized amplifiers. The BRT also has a variable hi-level DC offset turn-on circuit for easy installation into any OEM system. It is great for smaller stealth installations, as well as for motorcycles and recreational vehicles.

PBR300X4

PBR300X4

The Rockford PBR300X4 is a full-range 4-channel amplifier designed for stereo front/rear systems that requires little space. The BRT (Boosted Rail Technology) is an ultra efficient design that generates 300 Watts of power! The BRT also has a variable hi-level DC offset turn-on circuit for easy installation into any OEM system. Great for motorcycles and recreational vehicles.

PM-CL1

PM-CL1

The PM-CL1 is a white marine grade cast aluminum wakeboard tower speaker clamp designed for use with PM282W, PM282HW, and the PM2652W.

PM-CL1B

PM-CL1B

The PM-CL1B is a black marine grade cast aluminum wakeboard tower speaker clamp designed for use with the PM282W-B, PM282HW-B and the PM2652W-B.

PM-CL2B

PM-CL2B

The PM-CL2B is a black marine grade cast aluminum wakeboard tower speaker clamp designed for use with the PM2652W-MB and RM1652W-MB

PM100X1K

PM100X1K

The PM100X1 amplifier uses Rockford Fosgate’s patent pending BTL technology to provide you a very unique amplifier solution. This single channel amplifier utilizes the speaker output of the radio to not only provide the audio signal it needs, but also the power that runs the unit. This is done through a combination of the DC offset voltage commonly present and the audio AC signal itself.

Initially, it uses the DC offset voltage for its turn on power as well as primary amplification power. As volume is increased and the output power demand rises, the amplifier begins sharing the power load between the DC and AC signals. Once high volume is reached, the majority of the amplifiers power is provided from the AC signal only and is supplemented by its intenal storage bank.

This design allows it to actually charge its capacitive bank on the downside of the AC signal wave which is essentially unused power anyway. It also presents no more load to the radio than a standard 2 or 4 ohm speaker would thus keeping the radio amplifier circuit safe from low impedance conditions. This design allows the amplifier to be connected to a radio with a rated 20 watt output and produce up to 100 watts dynamically. The unit also features a 2/ 4 ohm input switch to match the amplifier to the output impedance rating of the radio circuit. For speaker protection, we incorporate and selectable high pass crossover with setting at 60, 80 and 100Hz.

In rare cases there is not enough DC voltage present to power the amp at turn on so an add on B+ wire is included and can be tied to other lower current circuits in its proximity. This design makes the amplifier ideal for OEM or aftermarket upgrades without having to use physically larger amplifiers as they can be hidden in the dash or doors of the vehicle. It is also IPX6 rated for those installs where moisture may be present.

PM210S4

PM210S4

The PM210S4 is a white 10” subwoofer designed with weatherproofing technology specific for use in marine watercraft or powersports applications. It features a stainless steel sport grille and is UV and moisture resistant. This woofer is so versatile, it can be used in sealed, vented or infinite baffle installations.